What's new
HK Proshop : For the Heckler and Koch Enthusiast

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

Resource icon

How to detail strip a P30/P30S/P30L/P30LS (Part 2 of 2) 1.0

No permission to download
Part 4 - Frame Re-assembly

Frame Re-assembly


Lightly oil the following parts:
• Trigger Axle
• Trigger Bar
• Trigger Bar Detent
• Trigger Bar Detent Spring
• Hammer
• Hammer Axle (or right-side Safety Lever shaft on a P30S/P30LS)
• Hammer Strut
• Hammer Spring
• Sear Axle
• Disconnector
• Control Latch
• Catch
• Sear with Decocker
• Flat Sear Spring


Step 1
• Insert the Trigger into the frame
• Locate the Trigger Axle hole and sleeve the 1/16 regular punch through the Trigger

uJqVoauq.jpg


Step 2
• Insert the 2 small strips of a coffee stirrer onto the Trigger Rebound Spring legs

40QpIQLavJ.jpg

JBm8TqA9uXee.jpg


• Insert the Trigger Rebound Spring into the frame. The spring's right leg (the longer of the two) will be on the right side of the frame

0ffGZYpuymFQ.jpg


• The spring's left leg will stick out behind the trigger

RbYtoEe2wVkx.jpg


• With the punch sitting flush against the right side of the frame, grab the Trigger Rebound Spring with the needle-nose pliers and push it down
• Sleeve the punch through the spring until it protrudes from the left side of the frame

rvHrxA.jpg


• Insert the Trigger Axle into the frame from the left side of the frame, backing out the punch

ATByUutQ6PA.jpg


• With the punch sitting flush against the right side of the frame, grab the Trigger Rebound Spring with the needle-nose pliers and push it down
• Sleeve the punch through the spring until it protrudes from the left side of the frame

rvHrxA.jpg


• Insert the Trigger Axle into the frame from the left side of the frame, backing out the punch

ATByUutQ6PA.jpg


• Tap the Trigger Axle into the frame so that the other end of the axle sits flush with the right side of the frame
• Remove the coffee stirrer strips

RbYtoEe2wVkx.jpg



Step 3
• Insert the right-side Slide Release Lever into the frame. Insert it at a 30-degree angle then flip it down

7adHemyiLY.jpg

hoEOZMLcima.jpg



Step 4
• Insert the left-side Slide Release Lever until it hits the Trigger Rebound Spring's right leg

C8lRUsQXlgNa.jpg


• Using the dental pick, lift up the spring's right leg, then push the Slide Release Lever in completely
• Release the spring's leg. It should rest upon the groove on the Slide Release Lever

2Mj3nQdNDN.jpg


Step 5
• Grab the Flat Sear Spring with the needle-nose pliers and insert it into the frame. Make sure it clicks.

9PUYMq1eKOl.jpg

k4CaubNvKI.jpg



Step 6
• Assemble the Trigger Bar Detent and its spring, then drop them into the frame. Push down lightly on the Trigger Bar Detent to lock it in place
• While pulling back lightly on the trigger, insert the Trigger Bar onto the eyelet on the trigger. Put a drop of oil where the Trigger Bar connects to the trigger

8RChCTKe.jpg


• Flip down the Trigger Bar so that it rests right on top of the Trigger Bar Detent

6vp6Nd8q3U.jpg



Step 7
• Drop the Hammer Strut into the frame
• A small piece of painter's masking tape would help secure the strut to the grip, preventing it from moving around while installing the hammer parts

FIxJRN1Ceo.jpg

tQWOs3.jpg



Step 8
If yours is a P30S or P30LS, skip to step 9


• Drop the Hammer into the frame

TWuSZniPceq.jpg


• While depressing lightly on the Trigger Bar, insert the Hammer Axle from the right side of the frame through the hammer, until it sits flush with the right side of the frame

Bc2W2CTEUX.jpg

IqFXmRkW7.jpg

z72BG02N.jpg


• The axle should also sit flush on the left side of the frame

EWStHkt.jpg



Step 9
If yours is a P30 or P30L, continue to step 10


• Drop the Hammer into the frame
• While depressing lightly on the Trigger Bar, insert the right-side Safety Lever through the hammer until it touches the right side of the frame

DlAShMfR.jpg


• Insert the left-side Safety Lever Detent Spring into the cavity on the frame

L7yIDefquan.jpg


• Drop the Safety Lever Detent on top of the spring

e1Li91.jpg

2VlaJ04Qz6JY.jpg


• Insert the tiny Safety Lever Retaining Pin into the lever, just enough so that it sits flush with the inside of the lever

cbot.jpg


• Mount the left-side Safety Lever onto the Hammer Axle

xScZtpFf.jpg


• While applying a little pressure on the left-side Safety Lever against the left side of the frame, tap the tiny pin into the lever using the 1/16 roll-pin punch, until it completely sits inside the lever, securing it in place. If you don't apply pressure on the lever against the frame, you won't be able to tap in the roll pin

LGXpYHUw.jpg



Step 10
• Insert the Disconnector

9YyQZTej4S.jpg

m1tSjWskK.jpg


• Insert the Sear with Decocker. It should go between the Flat Sear Spring and Hammer

fPFQ1DCZd.jpg

OeZCtxJszCRp.jpg


• Insert the Control Lever (aka Control Latch)

sOomK0I.jpg

Y4Zja0wM.jpg


• Insert the Catch. It should go between the Flat Sear Spring and Hammer Axle

PDOh2QMohGJy.jpg

iteHUVSZ1.jpg


• Sleeve the 3/32 punch from the right side of the frame through these parts, until it protrudes from the left side of the frame

5KAu1Zto.jpg


• Make sure the larger end of the Sear Axle is facing the left side of the frame
• Insert the axle from the left side of the frame, backing out the punch

kEElyhgX.jpg


• Both ends of the Sear Axle should sit flush with the frame

MDC1.jpg

Oo6K0I5OKBYy.jpg



Step 11
• Insert the Hammer Spring onto the Hammer Strut
• Make sure the Hammer Strut is positioned correctly in the frame

yUvQ7P.JPG

oI85wFBc7c.JPG


• Insert the other end of the Hammer Spring into the Hammer Spring Bearing (pay attention to the Hammer Spring Bearing orientation)
• Using the butt of a punch, push up lightly on the Hammer Spring Bearing and insert the retaining pin into the upper hole on the bearing (circled in RED). The lower hole is for the backstrap roll pin

g7TphYHIGN.jpg

8NCxa3cw.jpg
sta9i7nt.jpg



Step 12
• Mount the backstrap onto the grip
• Insert the backstrap roll pin and tap it in, using the 3/32 roll-pin punch

CSJe6Vynhy.jpg

aR5BCGis2.jpg


The frame is now completely re-assembled.

USwB7kQTrPWk.jpg
Author
TooSixy
Downloads
4
Views
3,794
First release
Last update
Rating
5.00 star(s) 1 ratings

Latest reviews

Best iv seen.
Top