First suppressor - 6.5" Form 1 can

drace

drace

Well-known member
Joined
Nov 23, 2020
Posts
65
Location
Florida
Feedback: 3 / 0 / 0
I got a few Form 1's back recently, one of them for this can I cooked up after browsing the Form 1 Suppressor boards for a while.

It's a Super Precision Concepts 6.500" Titanium ASR tube, 1.500" OD/ 1.375" ID.
1.500" blast chamber with a machined shoulder to space the baffles off from. SPC 60* dividers (2 HT SS, 6 Ti) with single clips.
YHM's ASR-thread three lug mount.

In my rush to function test it yesterday, I forgot to check POI shift. So I'm due for another range trip soon.

This is my first suppressor, and I think I'm picking up on a reason to start discriminating between "clean" and "dirty" ammunition. Until now, I haven't really noticed any one manufacturer's offerings being exceptionally dirty or clean.

When I was at the range I was shooting WWB 124gr NATO - since it's labeled "NATO," I think I may have been entertaining a notion that it was going to be better quality than your average WWB. I shoot lefty so I got blasted in the face with powder.

Any lefty shooters notice a significant difference between brands (re: debris coming out the ejection port) when shooting suppressed? I'm assuming subsonic rounds won't have nearly as much backblast through the ejection port, but I'll be shooting plenty of supersonic loads through it.


DSC_0047-2.jpg

9001_v4.jpeg
 
Wow, that looks a lot better than I expected a DIY can to look on an HK. I think a little cerakote will make it look as good as any factory can.

I think you've inspired me to research this further, and give it a shot myself. (y)
 
red said:
Wow, that looks a lot better than I expected a DIY can to look on an HK. I think a little cerakote will make it look as good as any factory can.

I think you've inspired me to research this further, and give it a shot myself. (y)
Click to expand...
It will absolutely be getting a Cerakote treatment (Graphite Black). Only problem is that I have to surrender it for the 2-4 week turnaround, and I'm not quite ready to let her go yet!

As far as building a can - if I can do it, you can do it. PM me and I'll send you some resources.
 
AGG said:
Excellent build. ;)
What locking piece are you using? :unsure:

Tony
Click to expand...
The one that came with the SP5. (This is a SP5 remark by Mike Otte.) Not sure which one that is. I know it's recommended to swap LP's for suppressing the K-guns - I haven't done much research regarding suppression of the full-size guns. Never had an excuse until now!
 
drace said:
The one that came with the SP5. (This is a SP5 remark by Mike Otte.) Not sure which one that is. I know it's recommended to swap LP's for suppressing the K-guns - I haven't done much research regarding suppression of the full-size guns. Never had an excuse until now!
Click to expand...

Just curious--- this may be of some value to you: :)


If it is running fine, and you are not planning on full auto, then you should be alright. ;)

Tony
 
Thanks Tony - was just searching for LP info and came across that chart immediately. Chart doesn't have info on the full-size guns in 9mm, but the anecdotal consensus is to leave it as-is.

I do run full auto quite a bit; I never have to clean the guns or pay for ammo. Only hitch is that it's all over once the alarm clock goes off.
 
drace said:
Thanks Tony - was just searching for LP info and came across that chart immediately. Chart doesn't have info on the full-size guns in 9mm, but the anecdotal consensus is to leave it as-is.

I do run full auto quite a bit; I never have to clean the guns or pay for ammo. Only hitch is that it's all over once the alarm clock goes off.
Click to expand...
😂 I know what you mean!!!
M.
 
drace said:
Thanks Tony - was just searching for LP info and came across that chart immediately. Chart doesn't have info on the full-size guns in 9mm, but the anecdotal consensus is to leave it as-is.

I do run full auto quite a bit; I never have to clean the guns or pay for ammo. Only hitch is that it's all over once the alarm clock goes off.
Click to expand...

You're welcome--- dreamer. ;)

Tony
 
You must log in or register to reply here.
Back
Top